Spring is coming and there are lots of plants to get started. Heres a customizable flower pot to help. Im not sure how well Pla really works as flower pot material (it should be fine), but you dont have to actually put real plants in them. Plastic plants - that would seem to be rather appropriate. Easter eggs might work, too. Jelly beans would also be a good choice for the smaller ones.

[update: Started some catnip seeds in the small beige pot with the vertical walls. I havent seen any seepage of water through the layers, but have it on a pad, just in case.] [update: the original catnip seedlings are now 6 weeks old - updated photo.]

[update: added a screen for the bottom of the pot to allow drainage while trying to keep the soil inside. Common practice is to put in a piece of a broken pot to cover the drain hole. Since I didnt think failed prints would be the same, I made a simple screen. See printing instructions for the special settings needed to print it.]

[update 2: Dont let your plant get root-bound. Besides the obvious health-of-your-plant reasons, turns out plant roots really like to get in the grooves between the print layers making the plant more difficult to remove for re-potting.]

So, why spend time and money printing out something you can easily buy for less than a dollar? Thats the wrong question for those of us on Thingiverse who print tons of often useless stuff.

A better question is why would I spend many hours building a flower pot algorithm in OpenSCAD. Since you asked, I was having fun re-discovering geometry and trigonometry and algebra - stuff I hadnt used since high school and stuff that most people, at that time in their lives, forget as soon as they can. I know I did. Who knew it would be useful some day?

Some notes on using the Customizer.

While the program tries to limit values to ranges that work well, its still possible to produce un-printable results if you color outside the lines, so to speak. For example: the design includes a fillet under the rim of the pot. This is intended to make the pot printable without any supports. It can look really strange and un-pot-like at extreme pot side angles and large rim sizes.

The side and base thickness can be left to the program (set each to 0). The program will set them based, roughly, on the base diameter chosen. However, you can set each dimension manually, if you wish.

If you use all the defaults, you get the pot pictured in the dimensions diagram.

As always, you can download the OpenSCAD code and get around the sanity limits. Ive tried to comment the heck out of it, but its the result of several different design attempts and a lot of iterations to get the calculations correct. Its not complicated, really. Just a bit messy.

I understand there are other, possibly easier, ways to create a pot. Excellent idea. Make one of your own and post the link here. Ill probably print it out.

Heres a brief overview of each parameter you can customize (all dimensions in mm or deg):

Base Diameter: the diameter of the outer edge of the pots base. The program limits this to a range: 10-350. When making a saucer, add from 10-20mm to the base diameter you used for the pot to get an appropriately-sized saucer.

Height of Pot: the height of the pot from the base to the top of the rim. The program limits this to a range: 8-350. Hint: a pots saucer is just a shorter, wider pot.

Pot SIde Angle: As the included picture shows, this is the number of degrees from vertical. Zero degrees gives a vertical side. The Customizer limits this to a range: 0-30deg in 1-degree increments.

Rim Side Angle: Also, the number of degrees from vertical. The Customizer limits this to a range: 0-30deg. The program also limits this - the rim angle cant be greater than the Pot Side Angle. It can be less, and actually looks a bit better if it is.

Height of Rim: The rim is the band around the top-edge of the pot. The Customizer limits this to a range: 0-200mm. The program limits the rim height to a bit less than the height of the pot. If you set this to zero, you get a round rim.

Rim Thickness: How thick should the rim be? The program limits this to a range: 0-10mm. Set this to zero to eliminate the rim.

Drain Hole: If you use this to pot plants, or simply for appearance, you can put a drain hole in the bottom of the pot by selecting Yes. The diameter of the hole is determined by the program and is based on the pot bases diameter. If you choose a drain hole, the program ignores the risers setting.

Pot Risers: In real life, the pot usually has some feet or something on the bottom to allow the drain to work. To make the pot printable without supports, I had to move the risers to the top of the saucer. If you want risers, you cant also have a drain hole. The program determines the dimensions of the risers based on the pot bases diameter.

Sidewall Thickness: The thickness of the pots walls. If you set this to zero, the program will calculate a value based on the pot bases diameter. You may also set this manually. The program limits this to a range: 1-6mm.

Base Thickness: The thickness of the pots base. If you set this to zero, the program will calculate a value based on the pot bases diameter and it will be a little thicker than the sidewalls. You may also set this manually. The program limits this to a range: 1-7mm.

Final note: the models included with this thing are examples and are not necessarily the ones in the photos.

Источник: https://www.thingiverse.com/thing:2806583

Автор: robertwallace

Лицензия: Creative Commons - Attribution